16 kanals analog input multiplexer (Intech 2100-M-R)

16 stk. PT100 føler indgange (2- eller 3-wire)

0/4-20mA eller 0-5/10V udgang

Forsyning 24VDC eller 230VAC

Styres af PLC med BCD kodning eller clock/reset pulser

DKK 4.895,00 ekskl. moms


  • 16 Channel Multiplexer
  • Field Programmable Inputs
  • Field Programmable Output
  • Input Types Available:
    • Pt100 RTD (-200~600°C) / (-330~1100°F)
    • MilliAmp (4~20 / 0~20mA)
  • Clock/Reset Channel Selection, or Binary Channel Selection
  • High Accuracy 0.1%
  • Compact DIN Rail Mount Enclosure
  • Easy to Install
  • Low Cost Expansion for PLCs
  • Solid State Switches for Reliability


The 2100-M is used extensively in industrial plants, with proven reliability and accuracy. It comes complete and ready to operate in a compact DIN rail mount enclosure.

The 2100-M (previously the EXPO-3) can multiplex up to 16 analogue inputs, into one input of a PLC or a Data Logging System. It uses solid state switches, making it extremely reliable and durable.

The 2100-M is widely used to expand up inputs on the 2400-A16 and 2100-A16, plus give economic easy accurate analogue input expansion on a PLC.

The PLC only requires two digital outputs and one analogue input to select and receive data from the 2100-M. For each additional 2100-M added to the system, only one more analogue input is required. (The typical fan-out for most PLC’s is up to eight 2100-M’s)

The 2100-M-I and the 2100-M-R are on board input span programmable. The output can be configured to a selection of industry standard output signals.

Ordering Information:

2100-M ordering table
Note 1) Minimum Range = Signal High – Signal Low.
Note 2) Maximum Range = Signal High – Signal Low.
Note 3) Sensor Break only applies to the RTD (-R) input model.
Note 4) Power supply ‘H’ is field selectable for ‘M’; and ‘M’ for ‘H’. Power supply ‘L’ must be ordered separately.

Notes on 2100-M-R (Input Range IR):
From the table above, you can chose a span (or Input Range IR) between -200 and +600°C. These are the limits – a span can not be chosen outside these limits.

However, to chose an actual span of -200 to 600°C is too wide to achieve good definition. I.e. If you want to see steps of 1°C or better, you will not achieve this with an actual span of -200 to 600°C. The minimum possible span is 20°C. The maximum possible span is 600°C. You need to chose a span that covers your working temperature range.
Examples of commonly used ranges include: 0~100°C, -50~50°C and 0~200°C.

Ordering code example for 2100-M with Pt100 RTD input (Input Model M = R), Input Range IR (or span) of 0~200°C, Output AO = 4~20mA, Channel Selection CS = Clock/Reset, Sensor Break SB = Upscale, Power Supply PS = 85~264Vac/dc:

2100-M-R- 0~200C – 4~20mA – CR – US – H


Analogue Input Multiplexer: 16 Single ended inputs
Each Multiplexer is span programmable within the specified input type as per below:
2100-M-R = RTD Pt100 (-200~600°C) (-330~1100°F)
2100-M-I = 4~20 / 0~20mA
2100-M-V = mV & V (-25~500mV and 0~10V DC) – No longer available, use the 2400-A16.
2100-M-T = Thermocouple (-100~1700°C) (-150~3000°F) – No longer available, use the 2400-A16.
Note 1:Minimum Thermocouple span = 200°C (400°F)
Note 2:2100-M-T requires a PI-T transmitter
Accuracy: <± 0.1% FSO Typical
Ambient Drift: < 00.1% / °C FSO Typical
Isolation on clock
& reset:
1kV AC/DC for 1 min
Operating Temperature: 0~60°C
Storage Temperature: -20~80°C
Operating Humidity: 5~85% RH Max. Non condensing
Housing: DIN & EN Rail mount
L = 195mm, W = 120mm, H=70mm
Power Supply: -H
85~264V ac/dc; 50/60 Hz; 10VA
23~90V dc; 10VA
10~28Vac/dc; 50/60Hz; 10VANote: Power supply H is field selectable for M; and M for H. Power supply L must be ordered separately.

Terminals and Layout:

2100-M terminal layout